ADVANTECH PCA-6654

PCA-6654/6654L Video Display Card for Flat Panel and CRT Copyright Notice This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements upon the rights of third parties which may result from its use. All brand and product names mentioned herein are trademarks or registered trademarks of their respective holders. Warning: Do not set "V/H SYNC+Blank" in the Award BIOS of your CPU card. If the Video Off Method of POWER MANAGEMENT SETUP in the Award BIOS is set on "V/H SYNC+Blank", the VGA chip 65550 on board the PCA-6654/6654L will not work properly after woken from power saving mode. Part No. 2002665400 1st Edition Printed in Taiwan July 1998 ii Packing List Before you set up the PCA-6654/6654L, make sure that the following materials have been included with the package, and that this manual is in good condition. If anything is missing or damaged, contact your dealer immediately: • PCA-6654/6654L card • PCA-6654/6654L User's Manual • PCA-6654/6654L installation driver Introduction PCA-6654 This is the standard version of the video display card. It contains PanelLink features, which enables it to be used with Advantech's FPM receiver series, including the FPM-37 and FPM-40. PCA-6654L This is the localized version of the video display card. It does not contain PanelLink features. It has only one port for connection to an LCD. iii PCA-6654 Board Layout PCA-6654L Board Layout iv Additional Information and Assistance 1. Visit the Advantech web sites at www.advantech.com or www.advantech.com.tw where you can find the latest information about the product. 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready: • Product name and serial number • Description of your peripheral attachments • Description of your software (operating system, version, application software, etc.) • Complete description of the problem • Exact wording of any error messages v Safety Instructions 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage. 7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS. 8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient over-voltage. 12. Never pour any liquid into an opening. This could cause fire or electrical shock. 13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user's manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE EQUIPMENT. The sound pressure level at the operator's position according to IEC 704-1:1982 is equal to or less than 70 dB(A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. vi Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Verletzungen hervorrufen. 7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden. 8. Beachten Sie beim AnschluB an das Stromnetz die AnschluBwerte. 9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden. 10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten. 11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden. 12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen. 13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden. 14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu überprüfen: a - Netzkabel oder Netzstecker sind beschädigt. b - Flüssigkeit ist in das Gerät eingedrungen. c - Das Gerät war Feuchtigkeit ausgesetzt. d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioni ert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist. Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70dB(A) oder weiger. DISCLAIMER: This set of instructions is given according to IEC704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. vii Contents Chapter 1 Introduction .................................................. 1 1.1 Description ..........................................................................2 1.2 Specifications ......................................................................3 1.3 Driver Support ...................................................................4 1.4 Utility Support....................................................................5 1.5 Video BIOS .........................................................................5 1.6 Simultaneous Display Mode ..............................................6 Chapter 2 Hardware Setup ........................................... 7 2.1 Hardware Configuration ...................................................8 2.2 Jumpers and Connectors ...................................................9 Setting jumpers ....................................................................9 2.3 Jumpers, Connectors and Switches ................................10 2.4 Connectors for Adjuster ..................................................10 J4 ........................................................................................10 J5 ........................................................................................10 J9 ........................................................................................10 2.5 Board Layout - Jumpers, Connectors and Switches.....10 2.6 Jumper and Switch Settings ............................................12 2.6.1 LCD signal level select (J6) ......................................12 2.6.2 LCD bias voltage select (MONO) (J7) .....................12 2.6.3 LCD bias voltage select (J8) .....................................13 2.6.4 LCD type select (SW1) .............................................13 2.6.5 LCD clock configuration select (for PanelLink only) (SW2) ........................................................................14 2.6.6 LCD control signal configuration select (for PanelLink only) (SW3) .............................................14 2.7 LCD Setup ........................................................................15 2.7.1 Preliminary................................................................15 2.7.2 TFT LCD Setup ........................................................16 2.7.3 DSTN LCD Setup .....................................................18 2.7.4 MONO LCD Setup ...................................................21 viii Chapter 3 Software Installation.................................. 25 3.1 Simultaneous Display Mode ............................................26 3.2 Installation for Windows 95 ............................................27 3.3 Installation for Windows NT ..........................................30 3.4 Installation for OS/2 ........................................................32 3.5 Further Information ........................................................35 Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) ................................... 37 4.1 Introduction ......................................................................38 4.2 Jumpers and Connectors .................................................39 Setting jumpers ..................................................................39 4.3 Connectors ........................................................................40 4.4 Connectors for Adjuster ..................................................40 J1 ........................................................................................40 J2 ........................................................................................40 J7 ........................................................................................40 4.5 Board Layout - Connectors .............................................41 4.6 Jumpers and Switches .....................................................42 4.7 Board Layout - Jumpers and Switches ..........................43 4.8 Jumper and Switch Settings ............................................44 4.8.1 LCD bias voltage select (J5) .....................................44 4.8.2 LCD signal level select (J8) ......................................44 4.8.3 LCD bias voltage select (MONO) (J13) ...................45 4.8.4 LCD input clock select (J14) ....................................45 4.8.5 Backlight level select (J15) .......................................45 4.8.6 Power down select (J16) ...........................................46 4.8.7 LCD type select (S1) .................................................46 4.8.8 LCD clock configuration select (S2) ........................47 4.9 LCD Setup ........................................................................48 4.9.1 Preliminary................................................................48 4.9.2 TFT LCD Setup ........................................................49 4.9.3 DSTN LCD Setup .....................................................53 4.9.4 MONO LCD Setup ...................................................58 ix Appendix A Pin Assignments - PCA-6654/6654L ..... 63 A.1 CRT Display (CN1) ..........................................................64 A.2 Flat Panel Display (CN2) .................................................65 A.3 Flat Panel Display Header (JP1) ....................................66 A.4 Keyboard Connector (J3) ................................................67 A.5 Backlight Power Connector (J10)...................................67 Appendix B Pin Assignments - FPM Receiver (PanelLink) .............................................. 69 B.1 Flat Cable Panel Display Header (JP3) .........................70 B.2 Flat Cable Panel Display Extension Header (JP4)........71 B.3 Backlight Power (J3)........................................................71 B.4 Extension Power (J6) .......................................................71 B.5 Flat Panel Display (J10)...................................................72 B.6 FFC Connector (A) For Flat Panel Display (J11) .........73 B.7 FFC Connector (B) For Flat Panel Display (J12) .........74 B.8 Keyboard Connector (J17) ..............................................74 x 1 Introduction • Description • Specifications • Driver Support • Utility Support • Video BIOS • Simultaneous Display Mode CHAPTER 1.1 Description The PCA-6654/6654L is based on the CHIPS VGA flat panel/CRT controller and is fully IBM VGA compatible. This controller offers a large set of extended functions and higher resolutions, and it supports simultaneous functioning. Since the PCA-6654/6654L VGA card is fully compatible, you do not require any special drivers to operate in standard modes. The enclosed software drivers allow you to take advantage of the extended features of the PCA-6654/6654L: • High performance in Microsoft Windows • Resolutions up to 1024 x 768 in graphics modes with 64 K colors • 640 x 480 resolution in graphics modes with 32K, 64K, and 16M colors • 132 column text mode Warning! Be sure to turn off the power and unplug all components before attempting to install or adjust the PCA-6654/6654L. Make sure the jumpers are set correctly before connecting the PCA-6654/6654L to your flat panel display. Incorrect jumper settings could damage your display. 2 PCA-6654/6654L User's Manual 1.2 Specifications Chipset: CHIPS 65550, integrated flat panel/CRT VGA controller Slot: High performance 32-bit PCI bus add-on card BIOS: 27C512, multiple panel support (8 panels built in) Memory: 2 MB EDO DRAM on board 256 K x 16 DRAM sockets for frame buffer (optional) Windows GUI (Graphic User Interface) accelerator: 64-bit Graphics Engine Simultaneous hardware cursor and pop-up window: 64 x 64 pixels by 4 colors 128 x 128 pixels by 2 colors Simultaneous CRT/LCD display: Available with TFT, DSTN, MONO and CRT Display support: Display centering and stretching features for optimal fit of VGA graphics and text on 800 x 600 and 1024 x 768 panels. CRT - Up to 1024 x 768 non-interlaced analog or multi-synch monitors with 64 K colors Flat panel - TFT LCD (Max resolution 1024 x 768, up to 64 K colors) DSTN LCD (Max resolution 1024 x 768, up to 4096 colors) MONO LCD (Up to 64 gray scales) VESA standards supported (40 K BIOS only): DPMS for CRT power-down (required for support of EPA Energy- Star Program) DDC for CRT plug and display control Chapter 1 Introduction 3 Connectors: MDR-26 for flat panel display (PanelLink) DB-15 for CRT Built-in 44-pin header for Advantech standard flat panel pin assignment Built-in housing to connect VR for adjusting contrast/brightness Power: On-board DC-DC converter supplies LCD bias voltage LCD backlight power supplied PanelLink: High speed and low EMI operation Flexible panel interface 1.3 Driver Support The software driver provides for the following systems: Software Name of VGA Driver Disk Microsoft Windows 95 PCA-6654 VGA Driver Windows 95 & NT 4.0 Microsoft Windows NT 4.0 PCA-6654 VGA Driver Windows 95 & NT 4.0 IBM OS/2 PCA-6654 VGA Driver OS/2 4 PCA-6654/6654L User's Manual 1.4 Utility Support The utility provides: CT.COM Enable CRT display only FP.COM Enable panel display only SM.COM Enable both displays at the same time REVERSE.EXE Reverse the displays' colors READBIOS.EXE Read the VGA BIOS information TESTDDC.EXE Test if the VGA BIOS supports DDC These utilities are only supported in DOS mode, and can only be used for testing. 1.5 Video BIOS The standard BIOS chip supports eight kinds of flat panel displays: 1024 x 768 DSTN (Sharp LM14X82) 640 x 480 MONO (Sharp LM64P89) 640 x 480 DSTN (Kyocera KCB6448BSTT-X5) 800 x 600 DSTN 640 x 480 SHARP TFT 640 x 480 18-bit TFT (Toshiba LTM10C209A) 1024 x 768 TFT 800 x 600 TFT (Toshiba LTM10C273) Note 1: To program the VGA BIOS to support the LCD only, you must use the file "6654-STN.DAT" located on the utility disk. Note 2: The Chips 65550 chipset cannot support a 1024 x 768 DSTN LCD on SM mode, due to bandwidth problems. Chapter 1 Introduction 5 1.6 Simultaneous Display Mode The PCA-6654/6654L supports simultaneous display to a CRT monitor and a flat panel display. The flat panel may be TFT, DSTN or MONO. If you use a DSTN LCD in this mode, the display must be under 16/256 colors or the CRT and flat panel screens will tremble. You must add a frame buffer with 512 K RAM and update the BIOS setup. Call us for assistance. 6 PCA-6654/6654L User's Manual 2 Hardware Setup • Hardware Configuration • Jumpers and Connectors • Jumpers, Connectors and Switches • Connectors for Adjuster • Board Layout - Jumpers, Connectors and Switches • Jumper and Switch Settings • LCD Setup - Preliminary - TFT LCD Setup - DSTN LCD Setup - MONO LCD Setup CHAPTER 2.1 Hardware Configuration The PCA-6654/6654L is based on chipset 65550 and has high performance, a simple configuration, and fully supported LCD/CRT. BIOS 16 8 Address Data RGB CRT H/V Sync Display 32 DDC CLK/Data Address Power-on 32 ENAVEE sequencing & Data 65550 DC-DC ENAVDD Converter VDDSAFE VEESAFE 24 Control Panel Data Flat Panel Panel Control Display Address Data Address Data 88 32 16 Panel Link 2MB Video 512KB Transmitter Memory Frame Buffer SiI 100/140 Data Pairs CLK Pair 3 32-Bit PCI Bus Panel Link Receiver SiI 101/141 Control Data 24/36 Flat Panel Display LCD Monitor Figure 2-1: System block diagram 8 PCA-6654/6654L User's Manual 2.2 Jumpers and Connectors Setting jumpers You can configure your PCA-6654/6654L to match the needs of your application by setting jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case, you would connect either pins 1 and 2 or pins 2 and 3. 3 2 1 Open Open Open Open Open Closed Closed Closed Closed Closed Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 The jumper settings are schematically depicted in this manual as follows: 1 Open Open Open Open Open Closed Closed Closed Closed Closed Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 A pair of needle-nose pliers may be helpful when working with jumpers. If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes. Chapter 2 Hardware Setup 9 2.3 Jumpers, Connectors and Switches Table 2-1: Jumpers, connectors, switches and their functions Label Function CN1 CRT display CN2 Flat panel display JP1 Flat panel display header J3 Keyboard connector J10 Backlight power connector J4 DSTN LCD contrast adjustment J5 MONO LCD contrast adjustment J9 LCD brightness adjustment J6 LCD signal level select J7 LCD bias voltage select (MONO) J8 LCD bias voltage select SW1 LCD type select SW2 LCD clock configuration select (for PanelLink only) SW3 LCD control signal configuration select (for PanelLink only) Please refer to Appendix A for pin assignments. 2.4 Connectors for Adjuster J4 This is a 3-pin housing. Connect a 500 Ω external VR to adjust V ; CON voltage range 0 ~ +2.8 V. J5 This is a 2-pin housing. Connect a 500 Ω external VR with on-board R-23 to adjust V ; voltage range +5 ~ +40 V or 0 ~ -40 V, EE depending on the jumper setting. J9 This is a 3-pin housing. Connect a 500 Ω external VR to adjust V ; BR voltage range 0 ~ +4.3 V. 10 PCA-6654/6654L User's Manual 2.5 Board Layout - Jumpers, Connectors and Switches J8: LCD bias voltage select J4: DSTN LCD contrast J7: LCD bias voltage adjustment select (MONO) SW2: LCD clock J5: MONO LCD configuration select contrast adjustment JP1: Flat panel display header SW1: LCD type select J9: LCD SW3: LCD control brightness signal configuration adjustment select J6: LCD signal J10: Backlight level select power connector J3: Keyboard CN1: CRT display connector CN2: Flat panel display Figure 2-2: Board layout - jumpers, connectors and switches Chapter 2 Hardware Setup 11 2.6 Jumper and Switch Settings Be sure the jumper and switch settings are correct before you install the card to the chassis. Refer to Fig. 2-2 for jumper and switch locations. For information about installing an LCD into your system, refer to Section 2. (LCD Setup) or Chapter 4 (FPM Receiver Setup) of this manual. 2.6.1 LCD signal level select (J6) Table 4-4: LCD signal level select (J6) * 5 V 3.3 V 1 1 * default setting 2.6.2 LCD bias voltage select (MONO) (J7) Table 4-5: LCD bias voltage select (MONO) (J7) +V [+5 V ~ +40 V] * -V [0 V ~ -40 V] EE EE 1 1 * default setting 12 PCA-6654/6654L User's Manual 2.6.3 LCD bias voltage select (J8) Table 4-3: LCD bias voltage select (J8) V [+5 ~ +40 V or 0 ~ -40 V for MONO LCD] EE 1 * V [0 ~ +2.8 V for DSTN LCD] CON 1 * default setting 2.6.4 LCD type select (SW1) Table 2-5: LCD type select (SW1) LCD type Pin 1 Pin 2 Pin 3 Pin 4 * 640 x 480 18-bit TFT OFF ON OFF ON 640 x 480 SHARP TFT ON ON OFF ON 800 x 600 TFT OFF OFF OFF ON 1024 x 768 TFT ON OFF OFF ON 640 x 480 DSTN ON OFF ON ON 800 x 600 DSTN OFF OFF ON ON 1024 x 768 DSTN ON ON ON ON 640 x 480 MONO OFF ON ON ON * default setting Chapter 2 Hardware Setup 13 2.6.5 LCD clock configuration select (for PanelLink only) (SW2) Table 2-6: LCD clock configuration select (for PanelLink only) (SW2) LCD type Pin 1 Pin 2 Pin 3 Pin 4 * TFT ON OFF ON OFF 640 x 480 DSTN OFF ON OFF ON 800 x 600 DSTN OFF ON OFF ON 1024 x 768 DSTN ON OFF OFF ON 640 x 480 MONO ON OFF ON OFF * default setting 2.6.6 LCD control signal configuration select (for PanelLink only) (SW3) Table 2-7: LCD control signal configuration select (for PanelLink only) (SW3) Pin number and setting details 1 * The LCD input data are latched on falling edge of clock → ON The LCD input data are latched on rising edge of clock → OFF 2 * The LCD control signals are latched on falling edge of clock → ON The LCD control signals are latched on rising edge of clock → OFF 3 The SiI100 differential clock output is divided by two → ON * The SiI100 differential clock output is divided by one → OFF * default setting 14 PCA-6654/6654L User's Manual 2.7 LCD Setup 2.7.1 Preliminary Make sure that your LCD is ready to match your PCA-6654/6654L card prior to setting jumpers and switches. You will need to know your LCD specifications, which will be among the following: 1. LCD type: TFT, DSTN or MONO 2. Number of pixels: 640 x 480, 800 x 600 or 1024 x 768 respectively 3. Supply voltage: 5 V or 3.3 V 4. LCD bias voltage for DSTN or MONO: Vmin., Vtyp., Vmax. 5. Backlight brightness voltage range in inverter You must also have the following parts ready: 1. LCD cable, to connect the LCD to JP1 2. Inverter, which must match your LCD specifications 3. Inverter power wire, to connect the inverter to J10 4. 500 Ω VR assembly with wire, for adjusting brightness 5. 500 Ω VR assembly with wire, for adjusting contrast (DSTN or MONO LCD only) Note: If your DSTN LCD does not have a built-in DC/DC converter, your must set up your LCD according to the MONO LCD setup procedures, except for when you set up SW1. Chapter 2 Hardware Setup 15 2.7.2 TFT LCD Setup Follow these steps: 1. Set SW1 according to the following table: Table 2-8: TFT LCD setup (SW1) LCD type Pin 1 Pin 2 Pin 3 Pin 4 * 640 x 480 18-bit TFT OFF ON OFF ON 640 x 480 SHARP TFT ON ON OFF ON 800 x 600 TFT OFF OFF OFF ON 1024 x 768 TFT ON OFF OFF ON * default setting 2. Set SW2 as follows, for all TFT LCDs: LCD type Pin 1 Pin 2 Pin 3 Pin 4 All TFT types ON OFF ON OFF 3. You do not need to set SW3. 4. Set J6 according to your LCD input power specifications: Table 2-9: LCD signal level select (J6) * 5 V 3.3 V 1 1 1 2 2 3 3 * default setting 5. You do not need to set J7 or J8. 6. Connect the LCD cable, inverter, inverter power wire, and VR assembly with wire to J9. (See Fig. 2-3.) 7. Plug the VGA card into the PCI slot. 8. Power on the system. 9. Adjust the screen brightness using the VR control. 16 PCA-6654/6654L User's Manual Inverter Figure 2-3: TFT LCD setup Chapter 2 Hardware Setup 17 Brightness VR Inverter power wire LCD cable PCA-6654/6654L 2.7.3 DSTN LCD Setup Follow these steps: 1. Set SW1 according to the following table: Table 2-10: DSTN LCD setup (SW1) LCD type Pin 1 Pin 2 Pin 3 Pin 4 640 x 480 DSTN ON OFF ON ON 800 x 600 DSTN OFF OFF ON ON 1024 x 768 DSTN ON ON ON ON 2. Set SW2 as follows, for all DSTN LCDs: LCD type Pin 1 Pin 2 Pin 3 Pin 4 All DSTN types ON OFF ON OFF 3. You do not need to set SW3. 4. Set J6 according to your LCD input power specifications: Table 2-11: LCD signal level select (J6) * 5 V 3.3 V 1 1 1 2 2 3 3 * default setting 5. You do not need to set J7. 18 PCA-6654/6654L User's Manual 6. Set J8 as follows: Table 2-12: LCD bias voltage select (J8) V CON 1 1 2 3 7. Connect the LCD cable, inverter, inverter power wire, and VR assembly. The VR assembly with wire for brightness control should be connected to J9, and the wire for contrast control should be connected to J4. (See Fig. 2-4.) 8. Plug the VGA card into the PCI slot. 9. Power on the system. 10. Adjust the screen brightness and contrast using the VR controls. Chapter 2 Hardware Setup 19 Inverter Figure 2-4: DSTN LCD setup 20 PCA-6654/6654L User's Manual Brightness VR Contrast VR Inverter power wire LCD cable PCA-6654/6654L 2.7.4 MONO LCD Setup Follow these steps: 1. Set SW1 as follows: LCD type Pin 1 Pin 2 Pin 3 Pin 4 640 x 480 MONO OFF ON ON ON 2. Set SW2 as follows: LCD type Pin 1 Pin 2 Pin 3 Pin 4 640 x 480 MONO ON OFF ON OFF 3. You do not need to set SW3. 4. Set J6 according to your LCD input power specifications: Table 2-13: LCD signal level select (J6) * 5 V 3.3 V 1 1 1 2 2 3 3 * default setting 5. Set J7 as follows: Table 2-14: LCD bias voltage select (MONO) (J7) +V -V EE EE 1 1 1 2 2 3 3 Chapter 2 Hardware Setup 21 6. Set J8 as follows: Table 2-15: LCD bias voltage select (J8) V EE 1 2 3 7. Plug the VGA card into the PCI slot. 8. Short J5. 9. Power on the system. 10. Adjust R-23 to be V max. EE 11. Power off the system. 12. Remove the jumper on J5. 13. Connect the LCD cable, inverter, inverter power wire, and VR assembly. The VR assembly with wire for brightness control should be connected to J9, and the wire for contrast control should be connected to J5. (See Fig. 2-5.) 14. Power on the system. 15. Adjust the screen brightness and contrast using the VR controls. 22 PCA-6654/6654L User's Manual Inverter Figure 2-5: MONO LCD setup Chapter 2 Hardware Setup 23 Brightness VR Contrast VR Inverter power wire LCD cable PCA-6654/6654L 24 PCA-6654/6654L User's Manual 3 Software Installation This chapter describes the installation and operation of the software drivers on the display driver diskettes included in your PCA-6654/6654L package. Sections in this chapter include: • Simultaneous Display Mode • Installation for Windows 95 • Installation for Windows NT • Installation for OS/2 • Further Information CHAPTER 3.1 Simultaneous Display Mode The 65550 VGA BIOS supports color TFT, color DSTN and monochrome LCD flat panel displays. It also supports interlaced and non-interlaced analog monitors (VGA color and VGA monochrome) in high-resolution modes while maintaining complete IBM VGA compatibility. Digital monitors (i.e. MDA, CGA, and EGA) are NOT supported. Multiple frequency (multisync) monitors are supported as analog monitors. Both CRT and panel displays can be used simultaneously. The PCA-6654/6654L can be set in one of three configurations: on a CRT, on a flat panel display, or on both simultaneously. The system is initially set to simultaneous display mode. In the utility diskettes, there are three .COM files which can be used to select the display. Simply type the file name at the DOS prompt: CT.COM Enables CRT display only FP.COM Enables panel display only SM.COM Enables both displays at the same time 26 PCA-6654/6654L User's Manual 3.2 Installation for Windows 95 a. Select "Start" , "Settings" , 1. "Control Panel". b. Double click the "display" icon. c. Choose the "Settings " label. d. Press the "Advanced Properties" button. a. Choose the "Adapter" 2. label. b. Press the "Change..." button. a. Press the "Have Disk..." 3. button. a. Insert the "VGA Driver 4. Windows 95&NT 4.0" disk into the floppy driver. b. Type "A: \WIN95P.244". c. Press the "OK" button. Chapter 3 Software Drivers and Utilities 27 5. a. Press the "OK" button. 6. a. "Chips and Tech 65550PCI" appear in the Adapter label. b. Press the "Close" button. 7. a. Press the "Yes" button b. Close all windows to reboot a. Repeat Step 1 on the 8. previous page of this manual. b. The "Chips" label appears in "Display Properties". c. Adjust the resolution and color. 28 PCA-6654/6654L User's Manual 9. a. Choose the "Chips" label. b. Adjust the refresh rate and display device. c. Press the "OK" button 10. a. Press the "OK" button to change the display setting. 11. a. Press the "OK" button to confirm the setting. END Chapter 3 Software Drivers and Utilities 29 3.3 Installation for Windows NT a. Select "Start" , "Settings" , 1. "Control Panel". b. Double click the "display" icon. c. Choose the "Settings " label. d. Press the "Display Type" button. 2. a. Press the "Change..." button. 3. a. Press the "Have Disk..." button. 4. a. Insert the "VGA Driver Windows 95&NT 4.0" disk into the floppy driver. b. Type "A:\WINNT4.115". c. Press the "OK" button. 30 PCA-6654/6654L User's Manual 5. a. Press the "OK" button. 6. a. Press the "Yes" button 7. a. Press the "OK" button b. Close all windows to reboot a. Repeat Step 1 on the 8. previous page of this manual. b. The "Chips" label appears in "Display Properties". c. Adjust the resolution, color and refresh rate. d. Press the "Test" button to check the setting. e. Press the "OK" button to confirm the setting. END Chapter 3 Software Drivers and Utilities 31 3.4 Installation for OS/2 1. a. Select "OS/2 System" , "Command Prompts" , "OS/2 Window". b. Insert the "VGA Driver OS/2" disk into the floppy driver. c. Type"A:",. d. Type"setup A: C:",. a. Press the "OK" button to 2. shut down. b. Reboot again. a. Select "OS/2 System", 3. "System Setup", "Display Driver Install". b. Enable "Primary Display". c. Press the "OK" button. a. Select 4. "Chips & Technologies 65550/554/555". b. Press the "OK" button. 32 PCA-6654/6654L User's Manual 5. a. Select "Install Using Defaults for Monitor Type". b. Press the "OK" button. 6. a. Type "A:\". b. Press the "Install..." button. 7. a. Insert the "VGA Driver OS/2" disk into the floppy driver. b. Press the "OK" button. 8. a. Press the "OK" button to shut down and restart the system. Chapter 3 Software Drivers and Utilities 33 9. a. Select "OS/2 System", "System Setup", "System". 10. a. Select the "Screen" tab. b. Adjust the resolution, color and refresh rate. END 34 PCA-6654/6654L User's Manual 3.5 Further Information For further information about installation of the PCI/SVGA in your PCA-6654/6654L, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: C&T web site: www.chips.com Advantech web sites: www.advantech.com www.advantech.com.tw Chapter 3 Software Drivers and Utilities 35 36 PCA-6654/6654L User's Manual 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) • Introduction • Jumpers and Connectors • Connectors • Connectors for Adjuster • Board Layout - Connectors • Jumpers and Switches • Board Layout - Jumpers and Switches • Jumper and Switch Settings • LCD Setup - Preliminary - TFT LCD Setup - DSTN LCD Setup - MONO LCD Setup CHAPTER 4.1 Introduction The SiI100/140 (added into the PCA-6654) and SiI101/141 (added into the FPM-40 receiver) are high-speed digital video/graphics interconnection devices capable of supporting VGA to XVGA resolutions for TFT panels and VGA to XGA resolutions for DSTN LCD panels. These devices are based on Silicon Image's PanelLink technology that currently enables reliable, scalable, high-speed data transmission over the same interface, from VGA to SVGA resolutions (and up to HDTV resolution in the future). The PanelLink transmitter incorporates an advanced coding scheme to enable TMDS signals to reduce EMI across copper cables and DC-balancing for data transmission over fiber optics. In addition, the advanced coding scheme enables robust clock recovery at the receiver to achieve high-skew tolerance for driving longer cable lengths. To maximize data recovery accuracy, the receiver triple oversamples and makes use of a data recovery algorithm to select the most reliable data sampling points. 38 PCA-6654/6654L User's Manual 4.2 Jumpers and Connectors Setting jumpers You can configure your FPM card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case, you would connect either pins 1 and 2 or pins 2 and 3. 3 2 1 Open Open Open Open Open Closed Closed Closed Closed Closed Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 The jumper settings are schematically depicted in this manual as follows: 1 Open Open Open Closed Closed Closed Closed 2 - 3 Closed 2 - 3 Closed 2 - 3 Open Open Closed Closed Closed 2 - 3 Closed 2 - 3 A pair of needle-nose pliers may be helpful when working with jumpers. If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes. Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 39 4.3 Connectors Table 4-1: Connectors Label Function JP3 Flat cable panel display header JP4 Flat cable panel display extension header J3 Backlight power J6 Extension power J10 Flat panel display connector J11 FFC connector (A) for flat panel display J12 FFC connector (B) for flat panel display J17 Keyboard connector J1 MONO LCD contrast adjustment J2 Brightness adjustment J7 DSTN LCD contrast adjustment Please refer to Appendix B for pin assignments. 4.4 Connectors for Adjuster J1 This is a 2-pin housing. Connect a 500 Ω external VR with on-board VR1 to adjust V SAFE; voltage range +5 ~ +40 V and 0 ~ -40 V. EE J2 This is a 3-pin housing. Connect a 500 Ω external VR to adjust V ; BR voltage range 0 ~ +4.3 V. J7 This is a 3-pin housing. Connect a 500 Ω external VR to adjust V EE SAFE; voltage range 0 ~ +2.8 V. 40 PCA-6654/6654L User's Manual 4.5 Board Layout - Connectors J3: Backlight power J1: MONO LCD contrast adjustment J2: Brightness adjustment JP3: Flat cable J17: Keyboard panel display connector J12: FCC connector (B) for flat panel display J10: Flat panel display J11: FCC connector connector (A) for flat panel display JP4: Flat cable panel display extension J7: DSTN LCD J6: Extension contrast power adjustment Figure 4-1: Board layout - connectors Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 41 4.6 Jumpers and Switches Table 4-2: Jumpers and switches Label Function J5 LCD bias voltage select J8 LCD signal level select J13 LCD bias voltage select (MONO) J14 LCD input clock select J15 Backlight level select J16 Power down select S1 LCD type select S2 LCD clock configuration select 42 PCA-6654/6654L User's Manual 4.7 Board Layout - Jumpers and Switches J5: LCD bias voltage select J15: Backlight level select J13: LCD bias S1: LCD type voltage select select (MONO) S2: LCD clock configuration select J14: LCD input J8: LCD signal clock select level select J16: Power down select Figure 4-3: Board layout - jumpers and switches Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 43 4.8 Jumper and Switch Settings Make sure the jumper and switch settings are correct before you install the FPM card to the chassis. Please refer to Appendix B for pin assignments. 4.8.1 LCD bias voltage select (J5) Table 4-3: LCD bias voltage select (J5) V [+5 ~ +40 V or 0 ~ -40 V for MONO LCD] EE 1 * V [0 ~ +2.8 V for DSTN LCD] CON 1 * default setting 4.8.2 LCD signal level select (J8) Table 4-4: LCD signal level select (J8) * 5 V 3.3 V 1 1 * default setting 44 PCA-6654/6654L User's Manual 4.8.3 LCD bias voltage select (MONO) (J13) Table 4-5: LCD bias voltage select (MONO) (J13) +V [+5 V ~ +40 V] * -V [0 V ~ -40 V] EE EE 1 1 * default setting 4.8.4 LCD input clock select (J14) Table 4-6: LCD input clock select (J14) * Divided by one Divided by two 1 1 * default setting 4.8.5 Backlight level select (J15) Table 4-7: Backlight level select (J15) * ENAV [high level] /ENAV [low level] EE EE 1 1 * default setting Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 45 4.8.6 Power down select (J16) Table 4-8: Power down select (J16) Power down * Normal * default setting 4.8.7 LCD type select (S1) Table 4-9: LCD type select (S1) LCD type Pin 1 Pin 2 Pin 3 Pin 4 * 640 x 480 DSTN ON OFF OFF OFF 800 x 600 DSTN ON OFF OFF OFF 1024 x 768 DSTN OFF ON OFF OFF TFT OFF OFF ON OFF * default setting 46 PCA-6654/6654L User's Manual 4.8.8 LCD clock configuration select (S2) Table 4-10: LCD clock configuration select (S2) Pin Pin Pin Pin LCD type Frequency/data latch edge/mode 1 2# 3 4 * TFT/16-bit DSTN divided by 1/negative/free running ON X ON ON TFT/16-bit DSTN divided by 1/positive/free running ON X OFF ON TFT divided by 2/negative/free running OFF X ON ON TFT divided by 2/positive/free running OFF X OFF ON 24-bit DSTN divided by 1/negative/blanked low ON X ON OFF NONE divided by 1/negative/blanked high ON X OFF OFF 24-bit DSTN divided by 2/negative/blanked low OFF X ON OFF 24-bit DSTN divided by 4/negative/blanked low OFF X OFF OFF * default setting # Termination resistor range selection: ON: 55 ~ 70 Ω OFF: 40 ~ 57 Ω (default) Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 47 4.9 LCD Setup 4.9.1 Preliminary Before you set the jumpers and switches, you need to know the LCD specifications, which will be among the following: 1. LCD type: TFT, DSTN or MONO 2. Number of pixels: 640 x 480, 800 x 600 or 1024 x 768 respectively 3. One pixel per clock or two pixels per clock in TFT LCD 4. LCD input data and control signals are latched on falling or rising edge 5. Supply voltage: 5 V or 3.3 V 6. LCD bias voltage for DSTN or MONO LCD: Vmin., Vtyp., Vmax. 7. Backlight brightness voltage range in inverter. You should also have: 1. PanelLink cable (refer to J10 and PCA-6654 CN2) 2. LCD cable (refer to LCD, JP3/JP4 or J11/J12 pin assignments) 3. Inverter (refer to LCD specifications) 4. Inverter power wire (refer to inverter and J3) 5. VR 500 Ω assembly with wire for adjusting brightness 6. VR 500 Ω assembly with wire for adjusting contrast (for DSTN or MONO LCD) Note: If your DSTN LCD does not have a built-in DC/DC converter, your must set up your LCD according to the MONO LCD setup procedures, except for when you set up SW1. 48 PCA-6654/6654L User's Manual 4.9.2 TFT LCD Setup Follow these steps: PCA-6654 1. Set SW1 according to the following table: Table 4-11: TFT LCD setup (SW1) LCD type Pin 1 Pin 2 Pin 3 Pin 4 640 x 480 18-bit TFT OFF ON OFF ON 640 x 480 SHARP TFT ON ON OFF ON 800 x 600 TFT OFF OFF OFF ON 1024 x 768 TFT ON OFF OFF ON 2. Set SW2 as follows, for all TFT LCDs: LCD type Pin 1 Pin 2 Pin 3 Pin 4 All TFT types ON OFF ON OFF 3. Set SW3 according to the following table: Table 4-12: LCD control configuration select (SW3) ON OFF 1 DATA EDGE Falling edge Rising edge 2 CLOCK EDGE Falling edge Rising edge 3 HALF CLOCK Divided by two Divided by one 4. You do not need to set J6, J7 and J8. FPM Receiver 5. Set S1 as follows, for all TFT LCDs: LCD type Pin 1 Pin 2 Pin 3 Pin 4 All TFT types OFF OFF ON OFF Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 49 6. Set S2 according to the following table: Table 4-13: LCD clock configuration select (S2) Frequency/data latch edge/mode Pin 1 Pin 2# Pin 3 Pin 4 divided by 1/negative/free running ON X ON ON divided by 1/positive/free running ON X OFF ON divided by 2/negative/free running OFF X ON ON divided by 2/positive/free running OFF X OFF ON # Termination resistor range selection: ON: 55 ~ 70 Ω OFF: 40 ~ 57 Ω (default) 7. You do not need to set J5. 8. Set J8 as follows: Table 4-14: LCD signal level select (J8) * 5 V 3.3 V 1 1 * default setting 9. You do not need to set J13. 10. Set J14 as follows: Table 4-15: LCD input clock select (J14) * Divided by one Divided by two 1 1 * default setting 50 PCA-6654/6654L User's Manual 11. Set J15 as follows: Table 4-16: Backlight level select (J15) * ENAV [high level] /ENAV [low level] EE EE 1 1 * default setting 12. Set J16 as follows: Table 4-17: Power down select (J16) Normal 13. Connect the PanelLink cable, LCD cable, inverter, inverter power wire, and VR assembly with wire to J2. (See Fig. 4-4.) 14. Plug the VGA card into the PCI slot. 15. Power on the system. 16. Adjust the screen brightness using the VR control. Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 51 Inverter PanelLink cable Figure 4-4: TFT LCD setup 52 PCA-6654/6654L User's Manual Brightness VR Inverter power wire LCD cable FPM receiver PCA-6654 4.9.3 DSTN LCD Setup PCA-6654 1. Set SW1 according to the following table: Table 4-18: TFT LCD setup (SW1) LCD type Pin 1 Pin 2 Pin 3 Pin 4 640 x 480 DSTN ON OFF ON ON 800 x 600 DSTN OFF OFF ON ON 1024 x 768 DSTN ON ON ON ON 2. Set SW2 according to the following table: Table 4-19: LCD clock configuration select (SW2) LCD type Pin 1 Pin 2 Pin 3 Pin 4 640 x 480 DSTN OFF ON OFF ON 800 x 600 DSTN OFF ON OFF ON 1024 x 768 DSTN ON OFF OFF ON 3. Set SW3 according to the following table: Table 4-20: LCD control signal configuration select (SW3) ON OFF 1 DATA EDGE Falling edge Rising edge 2 CLOCK EDGE Falling edge Rising edge 3 HALF CLOCK Divided by two Divided by one 4. You do not need to set J6, J7 or J8. Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 53 FPM Receiver 5. Set S1 according to the following table: Table 4-21: LCD type select (S1) LCD type Pin 1 Pin 2 Pin 3 Pin 4 640 x 480 DSTN ON OFF OFF OFF 800 x 600 DSTN ON OFF OFF OFF 1024 x 768 DSTN OFF ON OFF OFF 6. Set S2 according to the following table: Table 4-22: LCD clock configuration select (S2) Pin Pin Pin Pin LCD type Frequency/data latch edge/mode 1 2# 3 4 16-bit DSTN divided by 1/negative/free running ON X ON ON 16-bit DSTN divided by 1/positive/free running ON X OFF ON 24-bit DSTN divided by 1/negative/blanked low ON X ON OFF 24-bit DSTN divided by 2/negative/blanked low OFF X ON OFF 24-bit DSTN divided by 4/negative/blanked low OFF X OFF OFF # Termination resistor range selection: ON: 55 ~ 70 Ω OFF: 40 ~ 57 Ω 7. Set J5 as follows: Table 4-23: LCD bias voltage select (J5) V CON 1 54 PCA-6654/6654L User's Manual 8. Set J8 as follows: Table 4-24: LCD signal level select (J8) * 5 V 3.3 V 1 1 * default setting 9. You do not need to set J13. 10. Set J14 as follows: Table 4-25: LCD input clock select (J14) * Divided by one Divided by two 1 1 * default setting 11. Set J15 as follows: Table 4-26: Backlight level select (J15) * ENAV [high level] /ENAV [low level] EE EE 1 1 * default setting 12. Set J16 as follows: Table 4-27: Power down select (J16) Normal Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 55 13. Connect the PanelLink cable, LCD cable, inverter, inverter power wire, and VR assembly with wire for brightness to J2 and for contrast to J7. (See Fig. 4-5.) 14. Plug the VGA card into the PCI slot. 15. Power on the system. 16. Adjust the screen brightness and contrast using the VR controls. 56 PCA-6654/6654L User's Manual Inverter PanelLink cable Figure 4-5: DSTN LCD setup Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 57 Brightness VR Contrast VR Inverter power wire LCD FPM receiver PCA-6654 4.9.4 MONO LCD Setup PCA-6654 1. Set SW1 as follows: LCD type Pin 1 Pin 2 Pin 3 Pin 4 640 x 480 MONO OFF ON ON ON 2. Set SW2 as follows: LCD type Pin 1 Pin 2 Pin 3 Pin 4 640 x 480 MONO OFF ON OFF ON 3. Set SW3 according to the following table: Table 4-28: LCD control signal configuration select (SW3) ON OFF 1 DATA EDGE Falling edge Rising edge 2 CLOCK EDGE Falling edge Rising edge 3 HALF CLOCK Divided by two Divided by one 4. You do not need to set J6, J7 or J8. FPM Receiver 5. Set S1 as follows: Table 4-29: LCD type select (S1) LCD type Pin 1 Pin 2 Pin 3 Pin 4 MONO ON OFF OFF OFF 58 PCA-6654/6654L User's Manual 6. Set S2 according to the following table: Table 4-30: LCD clock configuration select (S2) Frequency/data latch edge/mode Pin 1 Pin 2# Pin 3 Pin 4 divided by 1/negative/free running ON X ON ON divided by 1/positive/free running ON X OFF ON # Termination resistor range selection: ON: 55 ~ 70 Ω OFF: 40 ~ 57 Ω 7. Set J5 as follows: Table 4-31: LCD bias voltage select (J5) V EE 1 8. Set J8 as follows: Table 4-32: LCD signal level select (J8) * 5 V 3.3 V 1 1 * default setting 9. Set J13 as follows: Table 4-33: LCD bias voltage setting (J13) +V * -V EE EE 1 1 * default setting Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 59 10. Set J14 as follows: Table 4-34: LCD input clock select (J14) * Divided by one Divided by two 1 1 * default setting 11. Set J15 as follows: Table 4-35: Backlight level select (J15) * ENAV [high level] /ENAV [low level] EE EE 1 1 * default setting 12. Set J16 as follows: Table 4-36: Power down select (J16) Normal 13. Connect the PanelLink cable to the VGA card and the FPM-40 receiver. (See Fig. 4-6.) 14. Plug the VGA card into the PCI slot. 15. Short J1. 16. Power on the system. 17. Adjust VR1 to be V max. EE 18. Power off the system. 19. Remove the jumper on J1. 60 PCA-6654/6654L User's Manual 20. Connect the LCD cable, inverter, inverter power wire, and VR assembly with wire for brightness to J2 and for contrast to J1. (See Fig. 4-6.) 21. Power on the system. 22. Adjust the screen brightness and contrast using the VR controls. Chapter 4 FPM Receiver Setup (PanelLink) (for PCA-6654 only) 61 Inverter PanelLink cable Figure 4-6: MONO LCD setup 62 PCA-6654/6654L User's Manual Brightness VR Contrast VR Inverter power wire LCD cable FPM receiver PCA-6654 A Pin Assignments - PCA-6654/6654L • CRT Display (CN1) • Flat Panel Display (CN2) • Flat Panel Display Header (JP1) • Keyboard Connector (J3) • Backlight Power Connector (J10) APPENDIX A.1 CRT Display (CN1) Table A-1: CRT display (CN1): Pin Signal Pin Signal 1 R 9 +5 V 2 G 10 GND 3B 11 NC 4 NC 12 DDC Data 5 GND 13 Horizontal sync 6 GND 14 Vertical sync 7 GND 15 DDC clock 8 GND 64 PCA-6654/6654L User’s Manual A.2 Flat Panel Display (CN2) Table A-2: Flat panel display (CN2) Pin Signal Pin Signal 1 +12 V 14 TX1+ 2 GND 15 +3.3 V 3 +12 V 16 GND 4 GND 17 TX2- 5 TXC- 18 TX2+ 6 TXC+ 19 KB_Data 7 +3.3 V 20 KB_Clock 8 GND 21 Power Down 9 TX0- 22 GND 10 TX0+ 23 +5 V 11 +3.3 V 24 GND 12 GND 25 +5 V 13 TX1- 26 GND Appendix A Pin Assignments - PCA-6654/6654L 65 A.3 Flat Panel Display Header (JP1) Table A-3: Flat panel display header (JP1) Pin Signal Pin Signal 1 +12 V 23 P14 2 +12 V 24 P15 3 GND 25 P16 4 GND 26 P17 5V SAFE 27 P18 DD 6V SAFE 28 P19 DD 7V SAFE 29 P20 EE 8 GND 30 P21 9 P0 31 P22 10 P1 32 P23 11 P2 33 GND 12 P3 34 GND 13 P4 35 SFHCLK 14 P5 36 FLM 15 P6 37 M/DE 16 P7 38 LP 17 P8 39 GND 18 P9 40 ENABKL 19 P10 41 NC 20 P11 42 NC 21 P12 43 NC 22 P13 44 NC 66 PCA-6654/6654L User’s Manual A.4 Keyboard Connector (J3) Table A-4: Keyboard connector (J3) Pin Signal 1 KB_Data 2 KB_Clock A.5 Backlight Power Connector (J10) Table A-5: Backlight power connector (J10) Pin Signal 1 +12 V 2 GND 3 ENABKL 4V BR 5 +5 V Appendix A Pin Assignments - PCA-6654/6654L 67 68 PCA-6654/6654L User’s Manual B Pin Assignments - FPM Receiver (PanelLink) • Flat Cable Panel Display Header (JP3) • Flat Cable Panel Display Extension Header (JP4) • Backlight Power (J3) • Extension Power (J6) • Flat Panel Display (J10) • FFC Connector (A) For Flat Panel Display (J11) • FFC Connector (B) For Flat Panel Display (J12) • Keyboard Connector (J17) APPENDIX B.1 Flat Cable Panel Display Header (JP3) Table B-1: Flat cable panel display header (JP3) Pin Signal Pin Signal 1 +12 V 2 +12 V 3 GND 4 GND 5V SAFE 6 V SAFE DD DD 7V SAFE 8 GND EE 9P0 10 P1 11 P2 12 P3 13 P4 14 P5 15 P6 16 P7 17 P8 18 P9 19 P10 20 P11 21 P12 22 P13 23 P14 24 P15 25 P16 26 P17 27 P18 28 P19 29 P20 30 P21 31 P22 32 P23 33 GND 34 GND 35 SHFCLK 36 FLM 37 M/DE 38 LP 39 GND 40 ENABKL 41 NC 42 NC 43 NC 44 NC 70 PCA-6654/6654L User’s Manual B.2 Flat Cable Panel Display Extension Header (JP4) Table B-2: Flat cable panel display extension header (JP4) Pin Signal Pin Signal 1V SAFE 2 +5 V DD 3 P24 4 P25 5 P26 6 P27 7 P28 8 P29 9 P30 10 P31 11 P32 12 P33 13 P34 14 P35 15 GND 16 GND B.3 Backlight Power (J3) Table B-3: Backlight power (J3) Pin Signal Pin Signal 1 +12 V 2 GND 3 ENABKL 4 V BR 5 +5 V Appendix B Pin Assignments - FPM Receiver (PanelLink) 71 B.4 Extension Power (J6) Table B-4: Extension power (J6) Pin Signal Pin Signal 1 +12 V 2 GND 3 GND 4 +5 V B.5 Flat Panel Display (J10) Table B-5: Flat panel display (J10) Pin Signal Pin Signal 1 +12 V 2 GND 3 +12 V 4 GND 5 TXC- 6 TXC+ 7 +3.3 V 8 GND 9 TX0- 10 TX0+ 11 +3.3 V 12 GND 13 TX1- 14 TX1+ 15 +3.3 V 16 GND 17 TX2- 18 TX2+ 19 KB_Data 20 KB_Clock 21 Power Down 22 GND 23 +5 V 24 GND 25 +5 V 26 GND 72 PCA-6654/6654L User’s Manual B.6 FFC Connector (A) For Flat Panel Display (J11) Table B-6: FFC connector (A) for flat panel display (J11) Pin Signal Pin Signal 1P0 2 P1 3P2 4 P3 5P4 6 P5 7 GND 8 GND 9P6 10 P7 11 P8 12 P9 13 P10 14 P11 15 GND 16 GND 17 P12 18 P13 19 P14 20 P15 21 P16 22 P17 23 GND 24 GND 25 P18 26 P19 27 P20 28 P21 29 P22 30 P23 Appendix B Pin Assignments - FPM Receiver (PanelLink) 73 B.7 FFC Connector (B) For Flat Panel Display (J12) Table B-7: FFC connector (B) for flat panel display (J12) Pin Signal Pin Signal 1 P24 2 P25 3 P26 4 P27 5 P28 6 P29 7 GND 8 GND 9 P30 10 P31 11 P32 12 P33 13 P34 14 P35 15 GND 16 GND 17 FLM 18 LP 19 GND 20 GND 21 SHFCLK 22 M/DE 23 GND 24 GND 25 V SAFE 26 V EE CON 27 V SAFE 28 V SAFE DD DD 29 V SAFE 30 V SAFE DD DD B.8 Keyboard Connector (J17) Table B-8: Keyboard connector (J17) Pin Signal Pin Signal 1 KB_Clock 2 KB_Data 3 NC 4 GND 5 +5 V 74 PCA-6654/6654L User’s Manual